"Alerted.org

Braider Operator - 2nd Shift

Location : MANSFIELD, TX, United States

Job Family : Manufacturing

Job Type : Regular

Posted : Jul 7, 2025

Job ID : 58085

Back to Search Results

Job Description

Save JobJob Saved

Operate either the NEB, OMA and/or TMW 24/36 braiders and monitor for proper product quality

ESSENTIAL FUNCTIONS:

+ Pull tooling and materials according to manufacturing specifications for applicable machine(s), such as springs, braid rings, tube guides, wound bobbin, core tube, etc.

+ Inspect tooling before using and track material used in WW3 system and Braider Logs

+ Set up applicable machine(s) according to manufacturing specifications (braid ring height, install tube guide, change deck/puller gear, unload/load carriers, unload/load bobbins, etc.) and mark defects/new preforms with the correct tape color

+ Measure and record OD and pitch on Hose Process Chart (SPC)

+ Run braided hose through wash tank and stage in hose coiling area for inspection

+ Maintain work area in clean and orderly fashion, follow 5s practices

+ Know and practice all safety regulations and quality guidelines

+ Report production issues to Direct Lead

+ Perform work of an equal or lower classification

DEPARTMENT SPECIFIC/NON-ESSENTIAL FUNCTIONS:

+ Work safely in accordance with regulations, standards, and procedures, and in a manner that eliminates unreasonable risk to health and the environment. Notify management of unsafe conditions or practices, unlawful activities and activities which present unreasonable health and/or environmental risk. Report all safety and/or environmental incidents to management immediately.

+ Prevent excess waste of product and/or components by operating the equipment in an efficient manner.

+ Participate in peer-based teams (i.e., Natural High Performance Teams), and work with groups to initiate and implement programs such as Lean Manufacturing and 5-S.

+ Other duties may be assigned at a later time.

MINIMUM REQUIREMENTS:

Education required:

High School diploma or GED

Experience:

Production work preferred but not required

Preferred Skills/Qualifications:

+ Good verbal and interpersonal communication skills

+ Basic knowledge and use of hand tools

+ Sound decision making skills

+ Good math, reading, writing skills

+ Demonstrated mechanical aptitude

+ Strong trouble shooting skills

+ Be able to exercise continuous mental, visual, and audio attention

+ Ability to work well in a team environment

Skills/Competencies:

1. Basic computer skills

2. Ability to monitor machine sounds to identify and diagnose changes in order to take appropriate action.

3. Vision: Near acuity and accommodation for reading information to perform job tasks.

4. Requires constant alertness to surroundings and product quality with attention to detail.

Physical Requirements:

None at All

(0%)

Occasional

(1-33%)

Frequent

(34-66%)

Continuous

(67-100%)

Lift/Carry

Up to 10 lbs

11-20 lbs

21-30 lbs

Bending

Twist/Turn

Reach Below Knee

Push/Pull

Squat/Kneel

Stand/Walk

Sit

Lifting Above Shoulders

Assessment:

Employee must pass Pre-employment screening

ORGANIZATIONAL RELATIONSHIPS/SCOPE:

+ Report directly to Value Stream Team Leader

+ Work closely with Maintenance to resolve issues with the equipment

WORKING CONDITIONS:

The employee may be subject to:

+ High noise levels from operating machines and equipment.

+ Physical hazards from operating machines and moving reels.

+ Work in areas where safety equipment will be required (steel toe shoes, eye protection, hearing protection)

+ Standing is required for extended periods of time. Walking, pushing, pulling, reaching, bending, turning, twisting, squatting, and lifting is performed on a regular basis

+ Requires high degree of manual dexterity, which could be performed under restrictive conditions

+ Requires flexible hours and short notice for overtime.

The employee may be required to follow other job-related instructions and to perform other job-related duties as requested, subject to all applicable state and federal laws.

DISCLAIMER:

The above statements are intended to describe the general nature and level of work being performed by employees assigned to this classification. They are not intended to be construed as an exhaustive list of all responsibilities, duties and skills required of employees assigned to this position

Parflex Division is a part of Parker Hannifin, a global leader in motion and control technologies for over 100 years. When you join Parker Hannifin’s Parflex Division, you are not just working on hoses and tubing, you are helping power the systems behind some of the most important vehicles, machines, and technologies in the world. At our Mansfield, Texas facility, we focus on innovation, safety, and purpose-driven work. We offer stability, great benefits, and the satisfaction of building parts that truly make a difference.

Parker is an Equal Opportunity and Affirmative Action Employer. Parker is committed to ensuring equal employment opportunities for all job applicants and employees. Employment decisions are based upon job related reasons regardless of race, ethnicity, color, religion, sex, sexual orientation, age, national origin, disability, gender identity, genetic information, veteran status, or any other status protected by law. However, U.S. Citizenship, Permanent Residency or other appropriate status is required for certain positions, in accord with U.S. import & export regulations.

(“Minority / Female / Disability / Veteran / VEVRAA Federal Contractor”)

If you would like more information about Equal Employment Opportunity as an applicant under the law, please go to Employees & Job Applicants | U.S. Equal Employment Opportunity Commission (https://www.eeoc.gov/employees-job-applicants)

Drug-Free Workplace

In accordance with Parker’s policies and applicable state laws, Parker provides for a drug-free workplace. Therefore, all applicants seeking employment with Parker will be subject to drug testing as a condition of employment.