- SpaceX (Hawthorne, CA)
- …good edge margins and alignment + Shim and/or trim parts as required + Select drill bits, reamers and/or countersinking tools for pilot and full size holes + Locate, ... drill pilot holes using drill motor and... drill pilot holes using drill motor and proper size drill bit(s)...installation of fasteners + Use solvents to clean surfaces prior to sealing or assembly + Apply sealant, alodine,… more
- SpaceX (Hawthorne, CA)
- …sequence per drawing, using correct tools (eg, rivet gun and bucking bar, drill motor, power screwdriver, C-squeeze, ratchet wrench, nut runner) + Shim and/or trim ... parts as required + Select drill bits, reamers and/or countersinking tools for pilot and...installation of fasteners + Use solvents to clean surfaces prior to sealing or assembly + Apply sealant, Alodine,… more
- SpaceX (Hawthorne, CA)
- …sequence per drawing, using correct tools (eg, rivet gun and bucking bar, drill motor, power screwdriver, C-squeeze, ratchet wrench, nut runner) + Facilitate and ... + Shim and/or trim parts as required + Select drill bits, reamers and/or countersinking tools for pilot and...installation of fasteners + Use solvents to clean surfaces prior to sealing or assembly + Apply sealant, Alodine,… more
- Northrop Grumman (Sunnyvale, CA)
- …wrenches, screwdrivers, respirator, protective clothing, electric forklift, floor operated cranes, drill press taps, slings, drill bits, reamers, micrometers, ... etc., as specified, where templates and/or detail drawings are provided. Operate drills to drill and tap holes and cut material to size and length according to… more
- Sacramento County (Sacramento, CA)
- …logged out if they have not submitted their applications and all documentation prior to 5:00 pm on the cut-off date. + Your application should highlight ... they have not submitted their applications and all documentation prior to 5:00 pm on the cut-off date. +...course of your qualifying work. + Bandsaw. + Hammer drill . + Pipe threader. + Planer. + Power … more
- SpaceX (Hawthorne, CA)
- …on Mars. METAL SPINNING TECHNICIAN (COPV) - MULTIPLE SHIFTS RESPONSIBILITIES: + Drill , ream, and countersink full-size holes in parts/assemblies, in proper sequence ... and to correct size using a drill motor, bits, reamers and countersinks to meets specified...configure and setup work pieces to meet machine requirements prior to machining, spin forming or heat treating +… more
- Aerotek (Newark, CA)
- …check and measure dimensions during welding process - Grind and deburr parts when necessary prior to welding - Check and straighten parts when needed - Prep all weld ... joints - Drill and tap with drill fixtures when required - Insure quality meets company and customer standards - Maintain tolerances as required on print - Able… more
- General Atomics (Adelanto, CA)
- …following templates, guides or specific dimensions and sequences. + Route, drill , trim, and install fasteners to blueprint dimensions and tolerances. Operate ... low-pressure spray gun. + Check expiration dates of materials prior to use, prepare proper mixes of resins and...common shop tools such as band saws, disk sanders, drill press, wood lathe, etc. + May require respirator… more
- Sacramento County (Sacramento, CA)
- …performance. General Qualifications Minimum Age Requirement: Applicants must be 18 years of age prior to appointment because of the hazards of the job, as defined by ... they have not submitted their applications and all documentation prior to 5:00 pm on the cut-off date. +...+ Mower + Power hedge trimmer + Weedeater + Drill + Pressure Washer + Blower 15 Select the… more
- United Airlines (San Francisco, CA)
- …etc.) for the completion of required tasks + Must possess a valid passport prior to application with 18 months validity remaining prior to its expiration ... passport, and you must have one in your possession prior to starting training as a Flight Attendant. +...+ Flight attendant trainees must successfully complete an evacuation drill in the water (pool) during training. + Must… more