"Alerted.org

Summary THIS IS A NATIONAL GUARD TITLE 32 EXCEPTED SERVICE POSITION. This National Guard position is for a Air Cargo Specialist, Position Description Number D1965000 and is part of the Georgia Air National Guard. This is a full-time, Excepted Permanent, dual status position which requires Air National Guard Membership. Area of Consideration: Open to all Active Duty Air Force, Air National Guard and Air Force Reserve members. Responsibilities As an Air Cargo Specialist, WG-5201-10, you will: Inspect a variety of airdrop equipment such as parachutes, multi loop lines, extraction transfer force couplings, latch assembly couplings, cable assembly couplings, actuator assembly, release cargo parachute M-1, lanyard arming wire, connector parachute, timer delay assembly, link lower suspension, link assembly single suspension type IV, link assembly heavy duty, link 4 point, parachute release single knife, bracket suspension, and tie down cargo quick release. Perform visual, dimensional, and operational inspection of the above mentioned equipment at the prescribed times, in accordance with warnings, cautions, and notes and ground precautionary messages (GPM), for safety of flight. Make judgmental decisions on proximity to tolerances and interrelated dimensions on timer delay systems of M-1 release, latch assembly couplings, cable assembly couplings, and actuator assembly. Inspects for burrs, rough spots, corrosion, pits, cracks, welds, cuts, foreign material, bends, damaged threads, adjusting collars, set screws, shank pins, and that timers activate within specifications. Use a wide variety of inspection processes and techniques, and many unique and specially designed instruments and gauges (i.e., tension meters, scales, micrometers, gauges, torque wrenches, and protractors). Perform airdrop inspections after priorities are set, work sequences are determined, and pertinent policy matters have been reviewed. Independently performs assignments at the aircraft where the supervisor is not readily available. Perform three separate inspections of airdrop loads or containers rigged for airdrop prior to the actual airdrop. Make decisions on a wide range of matters that may involve deviations and departures from past precedents and accepted practice or highly subjective judgments that could affect safety of flight and crew. The first inspection is a rigger inspection required by the field manual or technical order for that particular type of load. The second inspection is the "before loading inspection". Conduct inspections jointly with the Air Force Joint Airdrop Inspector (AFJAI). Complete the proper airdrop inspection form in the DD Form 1748 (Joint Airdrop Inspection Record) series and all sign the appropriate blocks to certify correct rigging of the load. The third inspection is on board the aircraft after the load is rigged for flight and airdrop. Perform inspection along with an AFJAI and the aircrew Load Master. Apply a variety of sophisticated techniques to inspect specialized and complex aircraft systems in accordance with Load Master's Manual. Inspect systems i.e. dual rail and lock settings and hydraulic systems for ramp and door and ADS arms for the ramp. Focus on dimensions of rigged airdrop loads IAW 13C5 (Parachute Cargo Repack Manual) and 13C7 (Rigging Loads for Special Operations) T.O. series; extraction/deployment systems; emergency aft restraint provisions; type and number of recovery parachutes; proper tension on pendulum line IAW-9, and hazardous cargo certification IAW AFJMAN 24-204 (Preparing Hazardous Materials for Military Air Shipments). Rig and prepare unilateral airdrop training loads to include type V or other airdrop platforms for airdrops. Fabricate container delivery systems loads, skid boards, and other associated airdrop items, as required. Receive, unpack, and inspect unit possessed parachutes. Clean, dry, inspect, and pack cargo parachutes after use. Maintain and repair a variety of fabric, rubber, and leather articles. Operate and perform minor maintenance on sewing machines, punch presses, stenciling machines, and other similar equipment. Perform inspections and repair of cargo, deceleration, and extraction parachutes, and is responsible for certification. Perform Joint Airdrop Inspections as the aerial port inspector. Perform technical order compliance modifications and modifications of parachutes and related items. Maintain an adequate stock level of current aerial delivery system equipment, components, and supplies. Serve as unit representative on the Aerial Delivery Review Panel and as a Joint Airdrop Inspector. May be tasked to attend Airdrop Review and Malfunction Analysis board meetings. Perform drop zone control operations as Drop Zone Controller/Safety Officer. Conduct weather observations, wind speed, direction determination, marking drop zone with navigation aids and timing points, establishing and maintaining air to ground and point to point radio communications, relaying information to aircraft and to the Range Control Officer. Direct and control all airdrop zone operations to ensure the safe operation and protection of aircraft, vehicles, personnel, and equipment. Perform other duties as assigned. Requirements Conditions of Employment Qualifications Military Grades: A1C - TSgt. Compatible Military Assignments: 42P300. GENERAL EXPERIENCE: Experience or training which demonstrates the knowledge of equipment and practices associated with inspecting a variety of airdrop equipment such as parachutes, multi loop lines, extraction transfer force couplings, latch assembly couplings, cable assembly couplings, actuator assembly, link lower suspension, link assembly single suspension type IV, link assembly heavy duty, link 4 point, parachute release single knife, bracket suspension, and tie down cargo quick release. SPECIALIZED EXPERIENCE: Must have at least 36 months experience involving inspecting a variety of difficult techniques used to examine complicated and interconnected components such as; burrs, rough spots, corrosion, pits, cracks, welds, cuts, foreign material, bends, damaged threads, adjustments, collars, set crews, shank pins, and that timers activate within specifications. Also, you will make judgmental decisions on proximity to tolerances and interrelated dimensions on timer delay systems of M-1 release, latch assembly couplings, cable assembly, couplings, and actuator assembly. PHYSICAL EFFORT: Work assignments require moderate to heavy physical effort. Employees frequently lift, carry, push, or otherwise handle items weighing up to 50 pounds. Frequently handles items weighing more than 50 pounds, but assistance is usually available with heavy items. Frequent standing, walking, bending, crouching, reaching, and stooping is required. Climbing and working in high places is required. WORKING CONDITIONS: Work is performed inside in a well-lighted, heated, and ventilated area, and outside during normal as well as inclement weather conditions. Incumbent may be subject to hazards from toxic fumes, high-pressure air, and high noise levels. Education You must provide transcripts or other documentation to support your Educational claims. To receive credit for Education, you must provide documentation of proof that you meet the Education requirements for this position. Additional Information If you are a male applicant who was born after 12/31/1959 and are required to register under the Military Selective Service Act, the Defense Authorization Act of 1986 requires that you be registered or you are not eligible for appointment in this agency (https://www.sss.gov/RegVer/wfRegistration.aspx).